Dugald Clerk developed the first two cycle engine in 1879. It used a separate cylinder which functioned as a pump in order to transfer the fuel mixture to the cylinder.6
In 1899 John Day simplified Clerk's design into the type of 2 cycle engine that is very widely used today.13 Day cycle engines are crankcase scavenged and port timed. The crankcase and the part of the cylinder below the exhaust port is used as a pump. The operation of the Day cycle engine begins when the crankshaft is turned so that the piston moves from BDC upward (toward the head) creating a vacuum in the crankcase/cylinder area. The carburetor then feeds the fuel mixture into the crankcase through a reed valve or a rotary disk valve (driven by the engine). There are cast in ducts from the crankcase to the port in the cylinder to provide for intake and another from the exhausst port to the exhaust pipe. The height of the port in relationship to the length of the cylinder is called the "port timing."
On the first upstroke of the engine there would be no fuel inducted into the cylinder as the crankcase was empty. On the downstroke the piston now compresses the fuel mix, which has lubricated the piston in the cylinder and the bearings due to the fuel mix having oil added to it. As the piston moves downward is first uncovers the exhaust, but on the first stroke there is no burnt fuel to exhaust. As the piston moves downward further, it uncovers the intake port which has a duct that runs to the crankcase. Since the fuel mix in the crankcase is under pressure the mix moves through the duct and into the cylinder.
Because there is no obstruction in the cylinder of the fuel to move directly out of the exhaust port prior to the piston rising far enough to close the port, early engines used a high domed piston to slow down the flow of fuel. Later the fuel was "resonated" back into the cylinder using an expansion chamber design. When the piston rose close to TDC a spark ignites the fuel. As the piston is driven downward with power it first uncovers the exhaust port where the burned fuel is expelled under high pressure and then the intake port where the process has been completed and will keep repeating.
Later engines used a type of porting devised by the Deutz company to improve performance. It was called the Schnurle Reverse Flow system. DKW licensed this design for all their motorcycles. Their DKW RT 125 was one of the first motor vehicles to achieve over 100 mpg as a result.14
Why take care of car paint?
Among the drivers are very popular preparations, which produce no doubt brilliance of automotive paint. Interestingly, many of these measures not only contains polishing agents, but also agents responsible for applying a protective coating on our car. Thanks to such treatment as pasting of the car, so we can not only improve the aesthetics of the car, but also the fact that the car paint will be preserved. This, in turn, it will be more durable and resistant not only to mechanical damage, but also resistant to corrosion and other adverse to paint processes. Concern for the car paint is so profitable, because we can thereby postpone the need for removal of rust and so on.
Autonomous car vs automated
Autonomous means having the power for self-governance.8 Many historical projects related to vehicle autonomy have in fact only been automated (made to be automatic) due to a heavy reliance on artificial hints in their environment, such as magnetic strips. Autonomous control implies good performance under significant uncertainties in the environment for extended periods of time and the ability to compensate for system failures without external intervention.8 As can be seen from many projects mentioned, it is often suggested to extend the capabilities of an autonomous car by implementing communication networks both in the immediate vicinity (for collision avoidance) and far away (for congestion management). By bringing in these outside influences in the decision process, some would no longer regard the car's behaviour or capabilities as autonomous; for example Wood et al. (2012) writes "This Article generally uses the term "autonomous," instead of the term "automated." The term "autonomous" was chosen because it is the term that is currently in more widespread use (and thus is more familiar to the general public). However, the latter term is arguably more accurate. "Automated" connotes control or operation by a machine, while "autonomous" connotes acting alone or independently. Most of the vehicle concepts (that we are currently aware of) have a person in the driver?s seat, utilize a communication connection to the Cloud or other vehicles, and do not independently select either destinations or routes for reaching them. Thus, the term "automated" would more accurately describe these vehicle concepts".9